Search Results

A previous study by the authors has shown an efficiency benefit of up to Δηi = 10 % for stratified operation of a high pressure natural gas direct injection (DI) spark ignition (SI) engine compared to the homogeneous stoichiometric operation with port fuel injection (PFI). While best efficiencies appeared at extremely lean operation at λ = 3.2, minimum HC emissions were found at λ = 2. The increasing HC emissions and narrow ignition time frames in the extremely lean stratified operation have given the need for a detailed analysis. To further investigate the mixture formation and flame propagation und these conditions, an optically accessible single-cylinder engine was used. The mixture formation and the flame luminosity have been investigated in two perpendicular planes inside the combustion chamber.

The official Indian accident statistics show that the number of road accidents and fatalities are one of the highest worldwide. These official statistics provide important facts about the current accident situation. It is suspected that for various reasons not all accidents are reported to the official statistic. This study estimates the degree of underreporting of traffic accidents with casualties in India. In order to get a national overview of the traffic accident situation it is necessary to improve the knowledge about underreported accidents. Therefore, the in-depth accident database of “Road Accident Sampling System India” (RASSI) was analyzed [1]. This project is organized by a consortium that has collected traffic accidents scientifically in four different regions since 2011 on the spot which have been reported either by police or by local hospitals and own patrol by RASSI engineers.

As automobiles become increasingly smarter, the need to understand within the automotive software the physical behavior of its parts is growing as well. The laws of physics governing such behavior are mostly formulated as differential equations, which today are usually created or obtained from various modeling tools. For solving them, the tools offer several solvers to satisfy the requirements of different problems. E.g. simple and fast explicit low order solvers for non-stiff problems and more complex implicit solvers for stiff problems. Though the modeling and code generation features as available in such tools are desirable for embedded automotive software, they cannot be used directly due to special restrictions with respect to hard realtime constraints. One such restriction is the organization of automotive software in components complying with the AUTOSAR standard which is not widely supported by the modeling tools.

Engine management systems combined with fuel injectors allow a precise fuel metering for a robust combustion process. Stricter emission legislations increase the requirements for these port fuel injection systems (PFI), whereas the price is still the main driver in the emerging low cost 2-wheeler market. Therefore, a holistic mechatronic approach is developed by Bosch, which allows an improved fuel metering over life time and furthermore provides new possibilities for diagnosis without changing the injector itself. This example of an intelligent software solution provides the possibility to further improve the accuracy of the fuel metering of an injector. By use of the information contained in the actuation voltage and current, the opening and closing times of the injector are derivable.

The Side View Assist is the World’s first rider assistance system for two-wheelers. This is a Blind Spot Warning system, which uses four ultrasonic sensors to monitor the surrounding of the rider. Whenever there is a vehicle (i.e. a car, truck, or another motorbike) in the rider’s blind spot, the technology warns the rider with an optical signal close to the mirror. This will allow the rider to avoid a collision when changing lanes. In the current vehicle application, Side View Assist is active at speeds ranging from 25 to 80 kilometers per hour and supports riders whenever the difference in relative speed to other road users is small. The system helps to improve safety especially in cities, where heavy traffic makes it necessary to change lanes more often. Originally such systems have been developed for cars and different system solutions for cars have been in serial production for several years. The challenge was to adapt these systems so they would work for two-wheelers as well.

In the low-cost segment for 2-Wheelers legislative, economic and ecologic considerations necessitate a reduction of the emissions and further improvement in fuel consumption. To reach these targets, the commonly used carburetors are being replaced by engine management systems (EMS). One option to provide these systems for acceptable and attractive system costs is to save a sensor device and to substitute its measure by an estimation value. In many motorcycles the rotor of the vehicle's alternator is rigidly attached to the crankshaft. Therefore, the voltage and current signals of the alternator contain information about the engine's speed, which can be retrieved by evaluating these electric signals. After further processing of this information inside the electronic control unit (ECU), the absolute crankshaft position can be obtained. A high-resolution speed signal without mechanical distortions like tooth errors is gained, whose signal quality equals the one of a common speed sensor.

To satisfy future emission classes, e.g. EU6c, the particulate number (PN) of Direct-Injection Spark-Ignition (DISI) engines must be reduced. For these engines, different components influence the combustion process and thus also the formation of soot particles and deposits. Along with other engine components, the injector nozzle influences the particulate number and deposits in both fuel spray behavior and nozzle “tip wetting”. In case of non-optimized nozzle layouts, fuel may impinge on the piston and the liner in an unfavorable way, which implies low-oxygen diffusive combustion by retarded vaporizing wall films. For the tip wetting, wall films are present on the actual surface of the nozzle tip, which is also caused by unadapted nozzles. For non-optimized nozzles, the latter effect can become quite dominant. This paper deals with systematic nozzle development activities towards low-deposit nozzle tips and thus decreasing PN values.

In recent years a new combustion phenomenon called Low-Speed Pre-Ignition (LSPI) occurred, which is the most important limiting factor to exploit further downsizing potential due to the associated peak pressures and thus the huge damage potential. In the past there were already several triggers for pre-ignitions identified, whereat engine oil seems to have an important influence. Other studies have reported that detached oil droplets from the piston crevice volume lead to auto-ignition prior to spark ignition. However, wall wetting and subsequently oil dilution and changes in the oil properties by impinging fuel on the cylinder wall seem to have a significant influence in terms of accumulation and detachment of oil-fuel droplets in the combustion chamber. For this reason, the influence of test fuels with different volatility were investigated in order to verify their influence on wall wetting, detachment and pre-ignition tendency.

On the way to automated driving, the installation rate of surround sensing systems will rapidly increase in the upcoming years. The respective technical progress in the areas of driver assistance and active safety leads to a numerous and valuable information and signals to be used prior to, during and even after an accident. Car makers and suppliers can make use of this new situation and develop integrated safety functions to further reduce the number of injured and even deaths in car accidents. Nevertheless, the base occupant safety remains the core of this integrated safety system in order to ensure at least a state-of-the-art protection even in vehicles including partial, high or full automation. Current networked safety systems comprehend a point-to-point connection between single components of active and safety systems. The optimal integration requires a much deeper and holistic approach.

In recent years concern has arisen over a new combustion anomaly, which was not commonly associated with naturally aspirated engines. This phenomenon referred to as Low-Speed Pre-Ignition (LSPI), which often leads to potentially damaging peak cylinder pressures, is the most important factor limiting further downsizing and the potential CO2 benefits that it could bring. Previous studies have identified several potential triggers for pre-ignition where engine oil seems to have an important influence. Many studies [1], [2] have reported that detached oil droplets from the piston crevice volume lead to auto-ignition prior to spark ignition. Furthermore, wall wetting and subsequently oil dilution [3] and changes in the oil properties by impinging fuel on the cylinder wall seem to have a significant influence in terms of accumulation and detachment of oil-fuel droplets in the combustion chamber.

CNG direct injection is a promising technology to promote the acceptance of natural gas engines. Among the beneficial properties of CNG, like reduced pollutants and CO2 emissions, the direct injection contributes to a higher volumetric efficiency and thus to a better driveability, one of the most limiting drawbacks of today’s CNG vehicles. But such a combustion concept increases the demands on the injection system and mixture formation. Among other things it requires a much higher flow rate at low injection pressure. This can be only provided by an outward-opening nozzle due to its large cross-section. Nevertheless its hollow cone jet with a specific propagation behavior leads to an adverse fuel-air distribution especially at higher loads under scavenging conditions. This paper covers numerical and experimental analysis of CNG direct injection to understand its mixture formation.

In the Indian two-wheeler market, legislation and customers demand for a reduction of emissions and an increase of fuel efficiency. For two-wheelers with engine management systems, a cost-efficient approach for this trend exploits that the periodical fluctuation of the engine speed of single cylinder engines contains useful information about its operating conditions. The present article focuses on the quality of the estimation of combustion phasing and air-fuel ratio of a 125cc single cylinder motorcycle engine, obtained from the evaluation of these fluctuations. The robustness of an oxygen sensor-less port fuel injection system can be increased by using the estimated air-fuel ratio to adapt the parameters of the fuel injection algorithm.

The paper presents a comparative study of various models used to estimate gas dynamics in internal combustion engine (ICE) ducts. 1D models provide a sufficient accuracy, but they are still not implementable on current ECUs. On the other hand, low order models can be real-time but their lack of accuracy and high calibration cost are still a challenging problem. This work aims at presenting a comparison of currently used gas dynamics models to predict transient phenomena in engine ducts. It emphasizes on 1D and low order models. To test under engine-like conditions, the intake path of a virtual engine implemented in GT-Power and a production two cylinder engine are used. Results show a contrast in the performance of the different models, which gives the possibility to evaluate the various approaches. Based on this assessment and depending on the application in hand, the models can be chosen properly to estimate the gas dynamics in internal combustion engine ducts.

The fuel-independent particulate emissions of a direct injection gasoline engine were investigated. This was done by running the engine with reference gasoline at four different loads and then switching to hydrogen or methane port fuel operation and comparing the resulting particulate emissions and their size distribution. Differences in the combustion characteristics of hydrogen and gasoline were accounted for by diluting the inlet air with nitrogen and matching the pressure or heat release traces to those of gasoline operation. Methane operation is expected to generate particulate emissions lower by several orders of magnitude compared to gasoline and hydrogen does not contribute to carbon soot formation because of the lack of carbon atoms in the molecule. Thus, any remaining particulate emissions at hydrogen gas operation must arise from non fuel related sources, e.g. from lubrication oil, metal abrasion or inlet air.

This paper presents the development of a novel direct coil cooling approach which can enable high performance for electric traction motor, and in further significantly reduce motor losses. The proposed approach focuses on bypassing critical thermal resistances in motor by cooling coils directly in stator slots with oil flow. Firstly, the basic configuration and features are shown: sealed stator slots to air gap, pressure reservoirs on both side of the slots and slot channels for oil flow. The key to enhance thermal performance of the motor here is based on introducing fluid guiding structure in the slot channels. Next, heat transfer in the channel with guiding structure is investigated by CFD and compared with bare slot channel without guiding structure. For studying the effectiveness of proposed cooling concept, numerical analysis is conducted to compare it with HEV favored oil impingement cooling.

This paper presents an overview of the evolution & revolution of automotive E/E architectures and how we at Bosch, envision the technology in the future. It provides information on the bottlenecks for current E/E architectures and drivers for their evolution. Functionalities such as automated driving, connectivity and cyber-security have gained increasing importance over the past few years. The importance of these functionalities will continue to grow as these cutting-edge technologies mature and market acceptance increases. Implementation of these functionalities in mainstream vehicles will demand a paradigm shift in E/E architectures with respect to in-vehicle communication networks, power networks, connectivity, safety and security. This paper expounds on these points at a system level.

The spatial distribution of internal exhaust gas recirculation (EGR) is evaluated in an optically accessible direct injection spark ignition engine using near infrared laser absorption to visualize the distribution of the H2O molecule. The obtained overall internal exhaust gas recirculation compares well to gas-exchange cycle calculations and the spatial distributions are consistent with those measured with inverse LIF. The experimental procedures described in this report are designed to be simple and rapidly implemented without the need to resort to unusual optical components. The necessary spectral data of the selected absorption line is obtained from the HITEMP database and is validated with prior experiments carried out in a reference cell. Laser speckle in the images is effectively reduced using a ballistic diffuser.

The emission of particulate matter from future GDI engines has to be optimized, to comply with more stringent emission standards such as EU6. Therefore, the mechanisms responsible for the formation of particles have to be analyzed in detail. The understanding of the in-cylinder processes, necessary for this purpose, can only be achieved by a complementary use of optically accessible single-cylinder engines as well as the numerical simulation. This however leads to great demands on the 3D flow simulation. In this paper the complete CFD approach, incorporating a detailed description of the entire underlying model chain is shown. Particularly the wall surface temperature and the temperature drop due to the interaction with liquid fuel spray were identified as important parameters influencing the spray-wall interaction and thus also the particulate emissions. Nevertheless, in conventional CFD models, the spray cooling cannot be captured because of an assumed constant wall temperature.

One promising application in the emission control is the Selective Catalytic Reduction (SCR) system for the reduction of nitric oxides from exhaust emissions. Previous works at the institute have highlighted the importance of accurate CFD turbulence modeling with respect to the turbulent mixing of ammonia vapor [1]. With the help of Laser Doppler Anemometry (LDA) measurements it was confirmed that RANS approaches are capable of predicting the velocity field adequately. In contrast, the turbulence level was underestimated for all RANS approaches [2]. Based on this work the paper at hand presents CFD results using Large Eddy Simulation (LES). The sensitivity of the solution with respect to spatial and temporal resolution as well as the boundary conditions is demonstrated. In accordance with the Kolmogorov theory grid sizes ranging from 3.2 to 20 million cells were investigated using LES methodology.

This paper focuses on the potentials of a Belt-Starter-Generator (BSG) in the context of an ultra-light vehicle prototype with a target curb weight of only 600 kg. Therefore, two hybrid approaches with a voltage level below 60 V are described and their potentials regarding electrical driving and CO2 reduction are analysed in detail. Introducing the ‘Cars Ultra-Light Technology’ (CULT) project, the holistic lightweight approach is described as a main requirement for the further hybrid investigations. In addition, a P2-hybrid structure with a 12 V BSG on the transmission input shaft enabled unique features despite the low voltage level and limited electrical power resources. The CO2 reduction for this powertrain combination is described and compared to a conventional stop start configuration. The validation process on a dynamic test rig is presented as well.